PLAN TO BUILD A SYSTEM OF TEMPERATURE AND MOISTURE OPERATING IN AIRCRAFT COMPONENT STORAGE

  • Ahmad Ridho budi luhur
  • Akhmad Musafa

Abstract

In this final project, a temperature and humidity control system for aircraft component storage has been designed using a PID controller and ON/OFF controller. This system is designed so that the warehouse component storage temperature of aircraft components, especially the avionic component (aviation electronic) which has a storage requirement at a temperature of 16-26 °C and humidity at 40-65% maintained at the reference temperature, so that the quality and state of components stored in the warehouse will stay awake his life span and abilities. The control system that was designed consisted of 1 unit 12VDC 10A power supply, 1 unit DC-DC Converter, 1 unit Arduino Uno microcontroller board, 4 DHT22 sensors, 1 unit 2 Channel Relay, 1 unit 180 ° servo motor, and 1 unit dehumidifier. The reference temperature is set at 24 °C and the reference humidity at 60%. The control system consists of a PID controller to control temperature and an ON / OFF controller to control humidity. When the warehouse room is fed with a central AC (air conditioner) flow, the sensor will read the temperature and humidity of the room. The sensor readings will be sent to Arduino to be compared with a predetermined set point. The temperature error value will be processed by the PID with an output control signal in the form of a PWM signal (50Hz) to control the rotation of the servo motor used to open or close the central AC flow. While the humidity error signal will be processed by the ON / OFF controller with an output signal in the form of an ON or OFF state for the relay that is used as a switch for the dehumidifier. The test results with the PID parameter values ​​Kp=75, Ki=40, and K =45 obtained by the heuristic method produces a good system response. The temperature can be controlled between 24 °C - 26 °C and humidity can be lowered when it is above 60%.

References

Engineering, G. M. F. (2017) Storage Requirements For Aeronautical Supplies.
[2] Hartono, N. B., Sumantri, B. and Wijayanto, A. (no date) ‘PENGATURAN POSISI MOTOR SERVO DC’, 2, pp. 1–9.
[3] Islam, H. I. et al. (2016) ‘Sistem Kendali Suhu dan Pemantauan Kelembaban Udara Ruangan Berbasis Arduino Uno Dengan Menggunakan Sensor DHT22 dan Passive Infrared (PIR)’, V(Lcd), pp. 119–124.
[4] Olatayo M. Olaniyan, Mutiu. A. Adegboye, O. F. I. and O. B. (2018) ‘Design and Implementation of a Temperature and Humidity Control System for a Poultry House’, 6(1), pp. 106–114.
[5] Rizaldi, A. and Purwanto (2018) ‘Rancang Bangun Pengontrol Suhu Dan Kelembaban Pada Proses Fermentasi Tempe Menggunakan Kontroler Proporsional’, pp. 199–203.
[6] Winarso, P. and Sofwan, A. (2005) ‘Rancang Bangun Sistem Pengendali Suhu dan Kelembaban Udara Pada Rumah Wallet Berbasis Mikrokontroller AT89C51’, 2005(Snati), pp. 101–104.
[7] Hartono, N. B., Sumantri, B. and Wijayanto, A. (no date) ‘PENGATURAN POSISI MOTOR SERVO DC’, 2, pp. 1–9.
[8] Wicaksono, H. (2004) ‘Analisa Performansi dan Robustness Beberapa Metode Tuning Kontroler PID pada Motor DC’, 4(2), pp. 70–78.
[9] Sawidin, S. (2018) ‘System Design Temperature and Humidity Control Room with Android’, (December). doi: 10.5120/ijca2018917813.
[10] Redmond, S., Free, T. and Direct, I. (2017) ‘Component Maintenance Manual with Illustrated Parts List Solid State Cockpit Voice Recorder System’, (012).
Published
2022-07-06
How to Cite
RIDHO, Ahmad; MUSAFA, Akhmad. PLAN TO BUILD A SYSTEM OF TEMPERATURE AND MOISTURE OPERATING IN AIRCRAFT COMPONENT STORAGE. MAESTRO, [S.l.], v. 5, n. 1, p. 97 - 108, july 2022. ISSN 2655-3430. Available at: <https://jom.ft.budiluhur.ac.id/index.php/maestro/article/view/410>. Date accessed: 29 mar. 2024.